An Easy Plumbing Guide for Installing a Bathtub
An Easy Plumbing Guide for Installing a Bathtub
Blog Article
Nearly everybody has their own unique notions about How to Install a Bathtub Yourself.
Setting up a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the job as well as are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This short article will help you mount a brand-new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be quite problematic because of the limited gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the called for position. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; then do the very same for the other tap.
Switch on the water system and also examine all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the tub as well as also inspect the overflow electrical outlet and the regular outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack a stiff seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our part on How to Install a Bathtub. Many thanks for spending some time to read our article post. Loved our blog entry? Please share it. Let other people check it out. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Show Details Report this page